Amarok/Development/Compiling: Difference between revisions
< Amarok | Development
Copy page from old wiki |
m Update compilation instructions to kf5 |
||
| (3 intermediate revisions by 2 users not shown) | |||
| Line 1: | Line 1: | ||
=Tarball Compilation Instructions for Amarok 2.x= | =Tarball Compilation Instructions for Amarok 2.x-3.x= | ||
Extract the downloaded tarball thus: | Extract the downloaded tarball thus: | ||
tar | tar xJf amarok-x.y.z.tar.xz | ||
:Obviously you must replace x.y.z with the version of Amarok you have downloaded, eg: | :Obviously you must replace x.y.z with the version of Amarok you have downloaded, eg: | ||
tar | tar xJf amarok-2.9.82.tar.xz | ||
* Change into the directory that was extracted from the tarball, it should have the form amarok-x.y.z, eg: | * Change into the directory that was extracted from the tarball, it should have the form amarok-x.y.z, eg: | ||
| Line 19: | Line 19: | ||
* Read the README file that is in this directory, it may contain specific information that you will need when attempting to build and install Amarok. | * Read the README file that is in this directory, it may contain specific information that you will need when attempting to build and install Amarok. | ||
* Check you have the [ | * Check you have the [https://invent.kde.org/multimedia/amarok/-/blob/master/README mandatory dependencies] Amarok requires. Alternatively you can look for find_package calls in CMakeLists.txt. If you aren't sure if you have these dependencies installed, then <tt>cmake</tt> will tell you. | ||
* Change into the build directory: | * Change into the build directory: | ||
| Line 27: | Line 27: | ||
and compile Amarok with the following commands: | and compile Amarok with the following commands: | ||
cmake .. -DCMAKE_INSTALL_PREFIX=` | cmake .. -DCMAKE_INSTALL_PREFIX=`kf5-config --prefix` | ||
make | make | ||
sudo make install | sudo make install | ||
| Line 39: | Line 39: | ||
:If you are compiling development version, please consider compiling with debug enabled: | :If you are compiling development version, please consider compiling with debug enabled: | ||
cmake .. -DCMAKE_INSTALL_PREFIX=` | cmake .. -DCMAKE_INSTALL_PREFIX=`kf5-config --prefix` -DCMAKE_BUILD_TYPE=debugfull | ||
:as this greatly helps us to fix crash bugs. | :as this greatly helps us to fix crash bugs. | ||
Latest revision as of 07:22, 17 April 2024
Tarball Compilation Instructions for Amarok 2.x-3.x
Extract the downloaded tarball thus:
tar xJf amarok-x.y.z.tar.xz
- Obviously you must replace x.y.z with the version of Amarok you have downloaded, eg:
tar xJf amarok-2.9.82.tar.xz
- Change into the directory that was extracted from the tarball, it should have the form amarok-x.y.z, eg:
cd amarok-2.x.y.z
- Create a build directory as to not pollute the sources:
mkdir amarok-x.y.z-build
- Read the README file that is in this directory, it may contain specific information that you will need when attempting to build and install Amarok.
- Check you have the mandatory dependencies Amarok requires. Alternatively you can look for find_package calls in CMakeLists.txt. If you aren't sure if you have these dependencies installed, then cmake will tell you.
- Change into the build directory:
cd amarok-x.y.z-build
and compile Amarok with the following commands:
cmake .. -DCMAKE_INSTALL_PREFIX=`kf5-config --prefix` make sudo make install
- If you are compiling and installing as a regular user, call cmake with
-DDBUS_INTERFACES_INSTALL_DIR=/home/someuser
- so that these files are not installed to a system location that you cannot write to.
- If you are compiling development version, please consider compiling with debug enabled:
cmake .. -DCMAKE_INSTALL_PREFIX=`kf5-config --prefix` -DCMAKE_BUILD_TYPE=debugfull
- as this greatly helps us to fix crash bugs.
- You're done! Type amarok to start Amarok.
Note that your cmake preferences are saved in CMakeCache.txt, so you don't have to have the -D options every time you run cmake.
ccmake will give you a nice ncurses interface.